Red Hat ENTERPRISE LINUX 4 - ADMINISTRATION Guia de Instalação Página 40
- Página / 97
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
1. At the detailed menu for the cluster (below the clusters menu), click Shared Fence Devices.
Clicking Shared Fence Devices causes the display of the fence devices for a cluster and
causes the display of menu items for fence device configuration: Add a Fence Device and
Configure a Fence Device.
2. Click Configure a Fence Device. Clicking Configure a Fence Device causes the display of a
list of fence devices under Configure a Fence Device.
3. Click a fence device in the list. Clicking a fence device in the list causes the display of a Fence
Device Form page for the fence device selected from the list.
4. Either modify or delete the fence device as follows:
To modify the fence device, enter changes to the parameters displayed. Refer to Appendix B,
Fence Device Parameters for more information about fence device parameters. Click Update
this fence device and wait for the configuration to be updated.
To delete the fence device, click Delete this fence device and wait for the
configuration to be updated.
Note
You can create shared fence devices on the node configuration page, also. However,
you can only modify or delete a shared fence device via Shared Fence Devices at the
detailed menu for the cluster (below the clusters menu).
3.6. Configuring Cluster Members
Configuring cluster members consists of initially configuring nodes in a newly configured cluster, adding
members, and deleting members. T he following sections provide procedures for initial configuration of
nodes, adding nodes, and deleting nodes:
Section 3.6.1, “Initially Configuring Members”
Section 3.6.2, “Adding a Member to a Running Cluster”
Section 3.6.3, “Deleting a Member from a Cluster”
3.6.1. Initially Configuring Members
Creating a cluster consists of selecting a set of nodes (or members) to be part of the cluster. Once you
have completed the initial step of creating a cluster and creating fence devices, you need to configure
cluster nodes. To initially configure cluster nodes after creating a new cluster, follow the steps in this
section. T he starting point of the procedure is at the cluster-specific page that you navigate to from
Choose a cluster to administer displayed on the cluster tab.
1. At the detailed menu for the cluster (below the clusters menu), click Nodes. Clicking Nodes
causes the display of an Add a Node element and a Configure element with a list of the nodes
already configured in the cluster.
2. Click a link for a node at either the list in the center of the page or in the list in the detailed menu
under the clusters menu. Clicking a link for a node causes a page to be displayed for that link
showing how that node is configured.
3. At the bottom of the page, under Main Fencing Met hod, click Add a fence device to this
level.
4. Select a fence device and provide parameters for the fence device (for example port number).
Chapter 3. Configuring Red Hat Cluster With Conga
37
- Red Hat Enterprise Linux 4 1
- Cluster Administration 1
- Edition 1.0 2
- Table of Contents 4
- 1. Document Conventions 9
- 1.2. Pull-quote Conventions 10
- 2. Feedback 11
- Introduction 12
- 1.2. Conga 15
- Figure 1.4 . luci cluster Tab 17
- 1.3.2. Cluster Status Tool 20
- 2.1. Compatible Hardware 22
- 2.2. Enabling IP Ports 22
- Important 26
- 2.4. Configuring max_luns 29
- 3.1. Configuration Tasks 33
- 3.2. Starting luci and ricci 33
- 3.3. Creating A Cluster 34
- 3.8. Adding Cluster Resources 45
- 4.2. Managing Cluster Nodes 50
- 5.1. Configuration Tasks 53
- $ ssh -Y root@nano -01 54
- # system-config-cluster 54
- 5.7. Adding Cluster Resources 72
- # chkconfig --del httpd 84
- # mkfs -t ext3 /dev/sde3 85
- Listen 192.168.1.100:80 85
- Click OK 87
- Fence Device Parameters 88
- Revision History 94
Manuais e produtos relacionados com Servidores Red Hat ENTERPRISE LINUX 4 - ADMINISTRATION
Servidores Red Hat ENTERPRISE LINUX 5 - GLOBAL NETWORK BLOCK DEVICE Manual do Utilizador
(16 páginas)
(16 páginas)
Servidores Red Hat NETSCAPE ENTERPRISE SERVER 6.1 - NSAPI PROGRAMMER GUIDE Manual do Utilizador
(148 páginas)
(148 páginas)
Servidores Red Hat NETSCAPE ENTERPRISE SERVER 6.1 - NSAPI PROGRAMMER GUIDE Manual do Utilizador
(66 páginas)
(66 páginas)
Servidores Red Hat NETWORK 3.6 - Especificações
(42 páginas)
(42 páginas)
(42 páginas)
Servidores Red Hat NETSCAPE ENTREPRISE SERVER 6.1 - INSTALLATION AND MIGRATION GUIDE Guia de Instalação
(114 páginas)
(114 páginas)
Electrolux IF53X manuals
Owner’s manuals and user’s guides for Unknown Electrolux IF53X.
We providing 1 pdf manuals Electrolux IF53X for download free by document types: User Manual
Comentários a estes Manuais